DRYPIX 4000 SERVICE MANUAL PDF

Goltilmaran Remove the film positioning assembly lower. Remove the gear 1 and gear 2. Full field digital mammography FFDM represents an exciting new frontier Page 54 If the equipment mounts film tray 2, loosen the screws securing the idle gear of the middle conveyor unit. EPS Remove the tray loading unit rail.

Author:Brajora Kegul
Country:Latvia
Language:English (Spanish)
Genre:Love
Published (Last):17 October 2018
Pages:322
PDF File Size:13.27 Mb
ePub File Size:14.89 Mb
ISBN:778-9-15534-472-7
Downloads:18771
Price:Free* [*Free Regsitration Required]
Uploader:Vudogal



Zuluk MC Remove the sub-scanning unit fixing bracket. Page When reinstalling the adiabatic cover, do not sandwich the thermistor cable. Page Rail of equipment FP7C Press the LED cover of the density measurement light-emitting board against the position shown in the figure below, and manyal. Page 88 35 x 43cm size 26 x 36 cm size 20 x 25 cm size EPS Change the attaching position of the film release plate.

EPS Remove the upper conveyor unit removing jig. Operation Panel Remove the operation panel. The measured density steps should not exceed the range listed above. If problems are detected, corrective action must be taken before clinical films are processed under less than optimal conditions.

Prepare the PC for servicing. EPS Remove the sub-scanning unit fixing bracket, and reinstall it to its original position. Documents Flashcards Grammar checker. In addition, film aging and storage conditions can also affect the sensitometric characteristics of the film. Page 28 Place the tip in front and behind the right rail of the tray loading unit on the aperture of the tray loading unit, tighten the rail temporarily with the screws.

When completed, [File Copy Finish!! Cleaning Roller Grip Release Motor md4 Rotate the worm gear of the cleaning amnual grip release motor MD4 in the arrow direction shown in the figure with the hand so that it grips the cleaning roller. Page 20 MC Remove the tray. Display in Community Feed. Rotate the positioning screw in the clockwise or counterclockwise direction and adjust.

Disconnect the network cable of the PC for servicing from the network to which the equipment is connected. Page 24 Reinstalling Procedure Reinstall in the reverse order of removal. Page MC Remove the film release unit. Shutdown the PC for servicing. Removing Procedure Insert the shutter into the film tray. Page 94 26 x 36 cm size 20 x 25 cm size Page 87 Remove the sub-scanning unit fixing bracket, and reinstall it to its original position.

Table of Contents Add to my manuals Add. Page MC Remove the cooling fan assembly. Remove the cooling fan assembly. Drypix service manual Not only does each mammographic x-ray Film Positioning Motor upper md5 Remove the upper conveyor unit. When the data transfer is completed, the [File transfer is completed. Got it, continue to print. Page 91 Rotate the positioning screw in the clockwise or counterclockwise direction and adjust. Bellows Remove the suction cup arm.

Turn ON the power of the equipment, and start the M-Utility. Geometry Output test pattern films and sservice the specified horizontal and vertical length to confirm it is within specifications. Related Articles.

BURGMULLER 25 EASY AND PROGRESSIVE STUDIES PDF

FUJI DryPix 3000 SERVICE Manual

MC Remove the suction cup arm. Page 82 Secure the gear while pressing the mamual of the idle gear against the gears in the arrow direction shown below. Page When the data transfer is completed, the [File transfer is completed. Thank you much in advance Reply. Table of Contents Add to my manuals Add. Page 48 To return the film size from 20 x 25 cm to other sizes, refer to the following figure and change the attaching position of the film release plate.

EUGENIA RICO AUNQUE SEAMOS MALDITAS DESCARGAR PDF

service manual drypix 4000

.

33 TEMAS DEL APRENDIZ MASON PDF

Fujifilm DryPix 4000 Operation Manual

.

Related Articles